English translation for "jet velocity"
|
- 喷出速度
喷气速度
喷射速度
射流喷速
射流速度
Related Translations:
main jet: （化油器）主量孔化油器主喷管昼油嘴主喷口主喷油嘴主喷嘴主射流
- Example Sentences:
| 1. | The regularlty of the maximum velocity ' s change for multi - stage rocket of parallel type when the effective jet velocity of every stage increases in order
各级有效喷速依次递增时并联型多级火箭的最大速度值变化规律 | | 2. | Notice the hydraulic jump that forms , and see how it changes as you vary the jet velocity , flux , and dish depth ( horizontal dish )
注意水跃的形成，当你改变喷射的速度，流量以及盘的深度（水平的盘）的时候，看看它是怎么变化的。 | | 3. | The experimental results showed that incipient boiling point decreased with increasing fluid subcooling and was independent of other factors , and that temperature overshoot enhanced with decreasing jet velocity and fluid subcooling
结果表明：沸腾起始过热度随液体过冷度增加而减小，与其他因素无关，而温度过头值则随射流速度和液体过冷度减小而增加。 | | 4. | The effects of jet velocity ratio and skew angle were addressed . several co - rotating minute vortexes on the turbulence boundary layer would coalesce together that leaded to a big vortex . the effect of the big vortex was greater than a single minute one
单排多个同向射流与主流作用所产生的独立小涡旋将在流向下游发生合并，形成大涡旋，大涡旋对边界层的作用效果要强于单个独立小涡旋。 | | 5. | A simple model for primary breakup of energetic liquid jets was established using unstable wave theory . based on the jet - embedding method , the jet - core shape , the distribution of jet velocity and the primary distribution of liquid drops were computed
使用不稳定波理论，建立了射流初始破碎的简化模型，采用射流嵌入法( je )进行了数值计算，得到了hy911射流核形状、速度分布以及液滴尺寸的初始分布。 | | 6. | The ratio of the length to the depth of scour hole decreases with the increasing scour depth , in spite of the reason is the increase of the air concentration , the decrease of the jet velocity or the decrease of the jet thickness . 5 . governing equations of the aerated jet flow are established
掺气对冲坑形态并没有实质性的影响，冲坑的宽深比随冲坑深度的减小而增大，无论造成冲坑深度减小的原因四） 1大学i学博士学位论文是掺气、降低流速还是减小入射水舌厚度，其变化规律都可用相同的直线关系表示。 | | 7. | The influences of the inlet tube angle , backpressure and driving jet velocity on static pressure distribution in the gas - solid injector are calculated , and the effects of the inlet tube angle on particle bulk phase concentration and axial mean speed of particles in the gas - solid injector are analyzed firstly . the predicament caused by lack of measuring means on the particle velocity in experiments is solved
分析了收缩角、背压和气体喷嘴出口速度对气固喷射器内静压分布的影响，以及收缩角对气固喷射器内固体颗粒体积浓度场和颗粒平均速度的影响，解决了喷射器内固体颗粒速度试验测试手段缺乏的困境。 | | 8. | A reasonable position of driving nozzle helps to achieve the maximum material flow that also depends on other parameters such as backpressure , properties of conveyed material and driving gas . it is observed that , an increase of convergent section angle is harmful to the pneumatic conveying system , and also influences on the mass flow rate of conveyed material , the distribution of static pressures in injector and the pressure drops of conveying pipe . in addition , within a reasonable scope of air mass rate , increasing the driving jet velocity is more advantageous than enlarging the dimension of driving nozzle
试验研究发现，气体喷嘴位置对气固喷射器的输送能力影响最大，气体喷嘴存在某一最佳位置，而这一最佳位置与背压、输送物料特性和输送风特性相关联；气固喷射器的收缩角对其输送能力、内部静压分布和输送管阻力特性均有适量影响，收缩角增大对整个输送系统均不利；在适当的输送风范围内，提高气体喷嘴出口速度比扩大气体喷嘴尺寸更为有利，但气体喷嘴出口速度过高会增加气固喷射器和输送管内的能量损耗，给输送带来不利的影响；系统背压与气固喷射器的气体喷嘴出口速度的选取有关。 | | 9. | Dilution and dispersion in constant horizontal flow and bottom multi - port discharging was studied in accordance with the hydraulic model test . the influence of diffusion parameters ( jet angle , jet velocity , number of nozzle , riser space ) and environmental parameters ( water depth , water velocity ) on dilution were analyzed . the experimental results show that environmental parameters have prominent effects on wastewater dilution and dispersion , in addition to that , diffuser design parameters have significant influence on wastewater dilution and dispersion . for bailonggang outfall zone , jet angel is 10 or so , nozzle number is 16 or so
借助于人工模型试验，分析了恒定横流底部多孔排放时扩散器设计参数(射流角度、射流速度、喷口个数) 、上升管间距)及环境参数(环境水深、环境流速)对污水近区稀释扩散效果的影响，实验结果表明，除了环境条件对污水稀释扩散效果影响明显之外，扩散器设计参数对污水的近区稀释扩散也有显著的影响，针对白龙港排放口水域，喷口射流角度宜控制在10左右，喷口个数取16个 |
- Similar Words：
- "jet vane" English translation, "jet vane actuation system" English translation, "jet vane adctuator" English translation, "jet vane control" English translation, "jet vane reaction" English translation, "jet velocity attenuation coefficient" English translation, "jet velocity distribution" English translation, "jet veneer drier" English translation, "jet ventilation grid" English translation, "jet ventilation procedure" English translation
|
|
|
